- “Pulse Sensor” already exists in your wishlist
-
1.3″ 240×240 RGB TFT IPS LCD Display Module – 7-Pin
The 1.3″ 240×240 RGB TFT IPS LCD Display Module is a compact colour display ideal for graphical interfaces, sensor readings, menus, icons, and embedded projects.
Key Features:
• 1.3-inch RGB TFT IPS display
• 240×240 pixel resolution
• Full-colour display
• Wide IPS viewing angles
• Compact square design
• 7-pin interface
• Suitable for SPI-based applications depending on version
• Compatible with Arduino, ESP32, ESP8266, STM32 and Raspberry Pi
• Ideal for graphics, text, icons and images
• Suitable for IoT, robotics and DIY electronicsKSh 800.00 -
12V 1 Channel Relay Module Wireless Remote Control Switch
The 12V 1 Channel Relay Module Wireless Remote Control Switch from Liqman Electronics provides reliable wireless ON/OFF control of electrical devices and loads, making it suitable for automation, security, and remote switching applications.
Key Features
- 12V DC operating voltage
- 1-channel relay output for ON/OFF control
- Wireless remote control operation
- Stable signal reception for reliable switching
- Supports AC and DC loads within the relay rating
- Compact and durable PCB design
- Supports common switching modes such as momentary, toggle, and latched operation
- Suitable for automation, security, access control, and DIY projects
KSh 1,200.00 -
12V DC 1/2″ Solenoid Valve – Normally Closed (NC)
Key Features:
- 12V DC operating voltage
- Normally Closed (NC) design
- 1/2-inch threaded inlet and outlet
- Automatic ON/OFF fluid control
- Suitable for water and compatible low-viscosity fluids
- Compact inline design
- Relay and MOSFET control compatible
- Compatible with Arduino and ESP32 projects
- Suitable for PLC automation systems
KSh 900.00 -
2 x 18650 Cell Holder Case
The 2 x 18650 Cell Holder Case from Liqman Electronics is a compact battery holder with an ON/OFF switch for powering Arduino, ESP32, robotics, IoT and other portable electronics projects.
Key Features:
- Holds 2 × 18650 Li-ion cells
- Built-in ON/OFF switch
- Durable ABS plastic housing
- Pre-attached leads for easy wiring
- Supports series or parallel configurations depending on model
- Lightweight and portable
- Stable battery contact terminals
- Suitable for rechargeable battery systems
- Ideal for DIY electronics and prototyping
KSh 100.002 x 18650 Cell Holder Case
KSh 100.00 -
3-Wheel Robot Car Chassis
This 3-wheel robot car chassis is a beginner-friendly mechanical base designed for building mobile robots. With two drive wheels and one caster wheel, it offers excellent maneuverability and is ideal for line-following, obstacle-avoidance, and remote-controlled robotics projects.
KSh 1,000.003-Wheel Robot Car Chassis
KSh 1,000.00 -
3S 40A 18650 BMS with Cell Balancing
The 3S 40A 18650 BMS with Cell Balancing from Liqman Electronics is a protection board for 3-series lithium-ion and Li-Po battery packs.
Key Features:
- 3S configuration for 11.1V nominal battery packs
- 40A continuous current rating
- Cell balancing for three battery cells
- Overcharge protection
- Over-discharge protection
- Overcurrent protection
- Short-circuit protection
- Temperature monitoring
- Compatible with 18650 lithium-ion and Li-Po cells
- Suitable for robotics, power tools and DIY battery packs
KSh 500.003S 40A 18650 BMS with Cell Balancing
KSh 500.00 -
4 Channel Relay Module – 5V
4 Channel Relay Module – 5V from Liqman Electronics for controlling multiple electrical loads with microcontrollers and automation systems.
Key Features
- Four independent electromagnetic relays
- 5V DC operating voltage
- Switching capacity up to 10A at 250VAC or 30VDC per channel
- NO, NC, and COM terminals
- Opto-isolation on each relay channel
- Active-LOW trigger inputs
- Onboard transistor drivers and flyback diodes
- LED status indicator for each channel
- Compatible with Arduino, ESP32, ESP8266, Raspberry Pi, and PLC systems
- Clearly labeled screw terminals and pin headers
KSh 600.004 Channel Relay Module – 5V
KSh 600.00 -
4 DOF Acrylic Robot Manipulator Arm Kit
The 4 DOF Acrylic Robot Manipulator Arm Kit from Liqman Electronics is an educational robotics kit designed for learning robotic arm mechanics, automation and programming. Its lightweight acrylic structure provides four degrees of freedom for base rotation, arm movement and mechanical gripping.
Key Features:
- 4 degrees of freedom (4-DOF)
- Durable acrylic construction
- Precision laser-cut mechanical parts
- Black finish
- DIY unassembled design
- Mechanical gripper for object handling
- Lightweight and easy to assemble
- Compatible with Arduino, ESP32, Raspberry Pi and other controllers
- Customizable with different servo motors
- Suitable for pick-and-place projects
- Ideal for STEM education, robotics training and prototyping
- Servo motors and controller board not included
KSh 1,000.004 DOF Acrylic Robot Manipulator Arm Kit
KSh 1,000.00 -
4 x AA Battery Holder Box with DC
The 4 x AA Battery Holder Box with DC from Liqman Electronics is a compact portable power holder for Arduino, ESP32, robotics, LED lighting and other low-power electronics projects.
Key Features:
- Holds 4 × AA batteries
- Built-in DC output connector
- Approximately 6V with alkaline batteries
- Lightweight and portable
- Durable ABS plastic construction
- Stable battery contact terminals
- Easy plug-and-play connection
- Suitable for Arduino, ESP32 and sensor modules
- Ideal for portable DIY electronics
KSh 150.004 x AA Battery Holder Box with DC
KSh 150.00











