• pH Sensor Module/pH meter kit

    The pH Sensor Module (0–14 pH) with BNC Electrode Probe from Liqman Electronics is a high-precision pH measurement module for water quality monitoring, hydroponics, aquariums, laboratories and Arduino projects.

    Key Features:

    • Full 0–14 pH measurement range
    • Glass pH electrode with BNC connector
    • Analog voltage output
    • 3.3V–5V DC operating voltage
    • ±0.1 pH accuracy after calibration
    • Fast response and stable measurements
    • Replaceable pH electrode
    • Compatible with Arduino, ESP32, Raspberry Pi and STM32
    • Low power consumption

  • Solar Panel 6V

    The Solar Panel 6V from Liqman Electronics is a compact 2W photovoltaic module for solar-powered electronics, battery charging, Arduino projects and renewable energy applications.

    Key Features:

    • 6V DC output
    • 2W maximum power
    • High-efficiency photovoltaic cells
    • Compact, lightweight design
    • Suitable for battery charging with a compatible charge controller
    • Compatible with Arduino, ESP32 and Raspberry Pi using suitable regulation
    • Ideal for IoT, solar lighting and DIY projects
    • Suitable for indoor or outdoor use under direct sunlight

    Solar Panel 6V

    KSh 800.00
  • Solar Panel 5V

    The Solar Panel 5V from Liqman Electronics is a compact 220mA photovoltaic module for powering low-power electronics, battery charging, Arduino projects and DIY renewable energy applications.

    Key Features:

    • 5V DC output
    • 220mA output current
    • Compact size: 135 × 64.7mm
    • High-efficiency photovoltaic cells
    • Lightweight and easy to integrate
    • Suitable for battery charging with compatible circuitry
    • Compatible with Arduino, ESP32 and Raspberry Pi using suitable power management
    • Ideal for IoT, solar lighting and DIY projects

    Solar Panel 5V

    KSh 650.00
  • Solar Panel 5V 220mA

    The Solar Panel 5V 220mA from Liqman Electronics is a compact photovoltaic module for small-scale power generation, battery charging, Arduino, ESP32, IoT and DIY renewable energy projects.

    Key Features:

    • 5V DC output
    • 220mA maximum current
    • Approximately 1.1W power rating
    • Compact and lightweight design
    • Silicon photovoltaic cells
    • Suitable for battery charging with a compatible controller
    • Ideal for outdoor sensors and IoT projects
    • Works with Arduino and ESP32 systems
    • Supports educational solar experiments
  • Pan-Tilt Bracket for Servo SG90S MG90S

    The Pan-Tilt Bracket for SG90S MG90S Servo from Liqman Electronics is a lightweight 2-axis mounting platform for camera positioning, sensor scanning, robotics and Arduino automation projects.

    Key Features:

    • 2-axis pan and tilt movement
    • Compatible with SG90, SG90S and MG90S servos
    • Lightweight plastic construction
    • Suitable for cameras and sensors
    • Screw-based assembly
    • Compatible with Arduino, ESP32 and Raspberry Pi projects
    • Ideal for object tracking and robotics
    • Compact design for DIY automation
  • 4 x AA Battery Holder Box with DC

    The 4 x AA Battery Holder Box with DC from Liqman Electronics is a compact portable power holder for Arduino, ESP32, robotics, LED lighting and other low-power electronics projects.

    Key Features:

    • Holds 4 × AA batteries
    • Built-in DC output connector
    • Approximately 6V with alkaline batteries
    • Lightweight and portable
    • Durable ABS plastic construction
    • Stable battery contact terminals
    • Easy plug-and-play connection
    • Suitable for Arduino, ESP32 and sensor modules
    • Ideal for portable DIY electronics
  • 2 x 18650 Cell Holder Case

    The 2 x 18650 Cell Holder Case from Liqman Electronics is a compact battery holder with an ON/OFF switch for powering Arduino, ESP32, robotics, IoT and other portable electronics projects.

    Key Features:

    • Holds 2 × 18650 Li-ion cells
    • Built-in ON/OFF switch
    • Durable ABS plastic housing
    • Pre-attached leads for easy wiring
    • Supports series or parallel configurations depending on model
    • Lightweight and portable
    • Stable battery contact terminals
    • Suitable for rechargeable battery systems
    • Ideal for DIY electronics and prototyping
  • Float Switch Liquid Level Sensor

    The Float Switch Sensor from Liqman Electronics is a simple liquid level detection switch for water tanks, pumps, aquariums, irrigation systems and automation projects.

    Key Features:

    • Accurate liquid level detection
    • Magnetic reed switch operation
    • Simple ON/OFF output
    • Normally Open / Normally Closed options
    • Compact and lightweight design
    • Easy installation and maintenance
    • Low power operation
    • Suitable for automatic pump control
    • Compatible with PLCs, Arduino, ESP32 and relay modules
  • W3230 AC110–220V Digital Temperature Controller

    The W3230 AC110–220V Digital Temperature Controller from Liqman Electronics is a compact thermostat for automatic temperature control in heating and cooling applications. It uses an NTC 10K waterproof probe to monitor temperature and control connected devices through a built-in relay.

    Key Features:

    • AC 110–220V wide voltage input
    • NTC 10K waterproof temperature probe
    • 1-meter sensor cable
    • Temperature range: -50°C to +120°C
    • 0.1°C resolution
    • Relay output for automatic load switching
    • Heating and cooling modes
    • Digital LED temperature display
    • Programmable temperature and hysteresis settings
    • Compact panel-mount design
    • Suitable for incubators, aquariums, greenhouses and automation
  • XH-M452 Digital Temperature & Humidity Controller Module (12V 10A) with SHT20 Sensor

    The XH-M452 Digital Temperature & Humidity Controller Module (12V 10A) with SHT20 Sensor from Liqman Electronics is an environmental control module designed for automatic temperature and humidity monitoring. It features an SHT20 digital sensor and dual relay outputs for independently controlling connected heating, cooling, humidifying and ventilation equipment.

    Key Features:

    • SHT20 temperature and humidity sensor
    • 12V DC power supply
    • Dual relay outputs
    • Relay capacity up to 10A
    • Temperature range: -20°C to 60°C
    • Humidity range: 0–100% RH
    • Control accuracy: 0.1°C / 0.1% RH
    • Dual LED digital display
    • Adjustable start and stop thresholds
    • Compact 65 × 55 × 28 mm design
    • Suitable for incubators, greenhouses, farming and automation
  • 45 Kinds of Sensor Module Kit

    The 45 Kinds of Sensor Module Kit from Liqman Electronics is a versatile collection of 45 sensor and electronic modules for Arduino, ESP32, Raspberry Pi, STM32 and other development platforms. It is suitable for learning, prototyping, robotics, IoT, automation and electronics projects.

    Key Features:

    • Includes 45 different sensor and module types
    • Compatible with Arduino, ESP32, Raspberry Pi and STM32
    • Supports digital and analog sensing applications
    • Easy-to-connect modules with standard pin headers
    • Ideal for STEM education and electronics training
    • Suitable for robotics, IoT and automation projects
    • Useful for prototyping and experimentation
    • Suitable for beginners, students and experienced developers
  • 4 DOF Acrylic Robot Manipulator Arm Kit

    The 4 DOF Acrylic Robot Manipulator Arm Kit from Liqman Electronics is an educational robotics kit designed for learning robotic arm mechanics, automation and programming. Its lightweight acrylic structure provides four degrees of freedom for base rotation, arm movement and mechanical gripping.

    Key Features:

    • 4 degrees of freedom (4-DOF)
    • Durable acrylic construction
    • Precision laser-cut mechanical parts
    • Black finish
    • DIY unassembled design
    • Mechanical gripper for object handling
    • Lightweight and easy to assemble
    • Compatible with Arduino, ESP32, Raspberry Pi and other controllers
    • Customizable with different servo motors
    • Suitable for pick-and-place projects
    • Ideal for STEM education, robotics training and prototyping
    • Servo motors and controller board not included

Main Menu